Shindaiwa EC7600 Manual do Operador Página 13
- Página / 84
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
EC7500.48
Pre-filter
13
Inspection and Maintenance
Inspection and Maintenance Requirements
IMPORTANT!
MAINTENANCE, REPLACEMENT,
OR REPAIR OF EMISSION CONTROL
DEVICES AND SYSTEM MAY BE
PERFORMED BY ANY REPAIR
ESTABLISHMENT OR INDIVIDUAL.
HOWEVER, WARRANTY REPAIRS
MUST BE PERFORMED BY A DEALER
OR SERVICE CENTER AUTHORIZED
BY SHINDAIWA CORPORATION
AND USE OF PARTS THAT ARE NOT
EQUIVALENT IN PERFORMANCE AND
DURABILITY TO AUTHORIZED PARTS
MAY IMPAIR THE EFFECTIVENESS OF
THE EMISSION CONTROL SYSTEM
AND MAY HAVE A BEARING ON THE
OUTCOME OF THE WARRANTY CLAIM.
Dust in the air cleaner will affect engine
life. The air filter must be cleaned every
time you start operating.
Clean the air filter once a day and
replace the filter every 20 hours of
operation according to the following
procedures. See Figure 22.
Pull the choke lever out so that dust will
not enter the carburetor.
Unscrew the knob on the cleaner cover
and remove the cleaner cover and filter.
Remove the pre-filter from the filter.
clean the pre-filter with soap and water
and let dry.
If compressed air is available, blow air
from inside the filter to remove dust. If
compressed air is not available, remove
dust by gently tapping the element on a
hard surface.
Replace the pre-filter onto the filter and
reassemble them into the filter housing.
Make sure both filter bolts are securely
tightened.
1.
2.
3.
4.
5.
6.
Cleaning the Air Cleaner
Remove the Filter and
Pre-filter
Figure 22
Unscrew the
Knob
Choke
Filter
WARNING!
Inspection and maintenance
should be done in a well ventilated
place and where there is no risk of fire.
IMPORTANT!
When cleaning the filter, the filter housing
and the inside of the cleaner cover should
also be cleaned.
Item What to do Daily Weekly Monthly As Required
Air cleaner Clean
■
Cut-off wheel Clean and
sharpen
■
Bolts/screws Check and
retighten
■
Fuel cap Check for leakage
■
Fuel tank Check for leakage
■
Wheel guard Check function
■
Clutch bearing Grease
■
Belt Check and adjust
■
Spark plug Check and clean
■
Cylinder fins Clean
■
Fuel filter Clean
■
Carburetor Adjust
■
Reinstall the cleaner cover and make
sure the knob is securely tightened.
7.
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.181 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais