Shindaiwa EC7600 Manual do Operador Página 15
- Página / 84
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
15
Loosen the two bolts in the belt guard
by one turn. See Figure 25.
Turn the tension screw so the washer
aligns with the mark on the clutch
cover.
Tighten the two bolts in the belt guard.
1.
2.
3.
Figure 25
Clutch Cover
Bolts
Mark
Belt Guard
Washer
Tension
Screw
Adjusting Belt Tension
Inspection and Maintenance (continued)
Figure 26
Tension
Screw
Clutch
Cover
Bolt
Belt Guard
Slide
forward to
remove
Figure 27
Replacing the Drive Belt
Loosen the tension screw. Loosen the
two bolts on the belt guard and remove
the belt guard by sliding it to the right.
See Figure 26.
Loosen the two bolts in the clutch cover
and remove the clutch cover.
Replace the old belt with a new one.
Reassemble the clutch cover and the
belt guard and adjust the belt tension.
Figure 27 illustrates the components.
1.
2.
3.
4.
Always check the condition of the cut-off
wheel before starting the engine. Make
sure there are no breaks, cracks or warps.
See Figure 28.
A faulty wheel must be replaced with
a new one!
The tips of a diamond wheel should be
sharpened regularly to maintain cutting
efficiency. See page 16.
Figure 28
Cracks
Missing Tips
Worn Tips
Distortion or Warps
Checking the Cut-off Wheel
WARNING!
Never use a wheel which
has breakage, cracks or distortion.
The wheel may break while operat-
ing and may result in serious injury.
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.177 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais